The CryO² is a revolutionary new, award wining product designed to reduce the temperature of the air/fuel intake charge thus creating power. Through the science of aerodynamics and cryogenics, Design Engineering has developed a system to harness the cryogenic properties of liquid Co² to lower the air/fuel intake charge by up to 60%. The system is modular and can be easily expanded. The CryO² system provides two methods of cooling the air charge and one method of cooling the fuel charge, all utilizing the same burst of liquid Co². Co² is readily available at any welding supply shop or where paintball guns are charged. At most welding supply locations it costs us about $22.00 to fill a 50lbs tank of Co2.  Welcome to the future of power.

Tanks and Install Kit

The foundation to every CryO² System. Must have this kit to utilize CryO² components. The kit includes a 5 or 10 pound Co² tank, cryogenic solenoid valve, all necessary fittings, 14 ft. stainless steel hose, full wide open switch, arming switch, and wiring kit. Only one kit is needed to operate all the CryO² components.

Cry02 Air Intake

The CryO² Air Intake consists of an aerodynamically designed bulb with a cryogenic chamber which is mounted in a 4" segment of air tube. The air passes over the bulb, heat is removed from the air charge resulting in a colder, denser, more powerful charge. Dyno testing showed a reduction in intake air temperature of more than 50 degrees. The CryO² Air Intake can be used on turbocharged, supercharged or naturally aspirated applications. Multiple units can be used for colder results. Installs in minutes and comes with silicone connection sleeve, hose clamps and connection / vent hose.

Cry02 Fuel Bars

The CryO² Fuel Bar is a billet aluminum extension to the fuel line with a cryogenic chamber. The bar is charged with liquid Co² and freezes to -80 degrees f. Heat is removed from the fuel as it passes through resulting in a colder fuel charge. The CryO² Fuel Bar comes in -6AN and -10AN (can be reduced for -8AN) fuel line size. Four cryo-ports allow versatility of installation. Comes complete with vent plug, cryo-port plugs and connection/vent hose. The CryO² Fuel Bar can be used alone or in conjunction with other Co² components. It comes either anodized or polished with engraved DEI flame logo.

Cry02 Intercooler Sprayer

The CryO² Intercooler Sprayer mounts directly to the front of the intercooler or aftercooler and vents the liquid Co² directly onto the cooling fins, thus enhancing the performance of the intercooler by more than 50%. This component must always be the last in the CryO² system as it vents the liquid Co² charge.

CryO2 Intercooler Water Sprayer

DEI’s CryO2™ Intercooler Water Sprayer Kit was designed to be used by itself or in conjunction with DEI’s CryO2 Intercooler Sprayers as a way to supercool intercoolers.

By misting an intercooler’s surface with the Water Sprayer and then venting CO2 on the intercooler’s cooling fins, the intercooler is further chilled resulting in a cooler denser intake charge enhancing a vehicles performance for extended periods of time. Each Intercooler Water Sprayer Kit comes complete with reservoir, mounting hardware, flexible hose lines, wiring, push button activation switch, nozzle tubes, connectors and installation instructions.

Cry02 Purge Systems

The dramatic purge effect that people have come to love is now availiable at a fraction of the cost of other systems on the market. They can be used as a vent to a CryO2 system or as a stand alone show system. Must be used with a CryO2 Tank and Install kit (#080100 or #080102). The purges come in single or dual vents and the supply line can be split multiple times for multiple bursts around the car. You can also use the purge system seperate from the CryO2 performane system buy utilizing the purge kits that includes a solenoid vave and extension hose. This set-up will seperate the performance from the show purge.